LS2 FF908 Strobe II Monza White Blue Red – Flip-Up Commuter Helmet ECE 22.06 P/J

Monza is the racing graphic of the four: hard-edged blocks that sweep forward along the shell and break across the chin bar so the pattern still lines up closed. In white with blue and red it is the most conventional and the most legible of the twelve — the combination that reads as a motorcycle helmet from fifty metres.

What SHARP measured, and where this helmet sits

The Strobe2 replaced a helmet SHARP had already tested, which makes for an unusually direct comparison. The previous FF902 Scope earned three stars under the old ECE 22.05 regime in 2022. This helmet earned four under ECE 22.06 in August 2026 — a tougher standard, tested at more sites and more speeds, with rotational acceleration measured for the first time.

Going up a star while the test got harder is the strongest evidence in this table that the money went into the shell rather than into the paint.

About the Monza White Blue Red graphic

This is Monza on a white base, and the base is what makes it work. White carries the forward blocks around the brow and chin bar, blue fills the flanks, and red appears in small quantities at the edges where it draws the eye without taking over. Under a gloss clear coat the block edges stay knife-sharp; a matt lacquer would soften exactly the boundaries the design depends on. Two practical consequences follow from the large white area, and both are worth having on a commuter helmet: it is the most visible helmet in the Monza family at dusk and in rain, and it runs cooler in standing traffic than either of its darker siblings because most of the shell reflects rather than absorbs.

Three shells, and what KPA actually is

A word on what a polymer shell does in a crash, since it differs from a composite. Fibre shells are stiff, spread load quickly across a wide area, then delaminate. A thermoplastic flexes further before failing, spreading the impact over more time rather than more area. Both approaches work — ECE and SHARP care about the head inside, not the route taken. KPA gets there by deforming, and it did so well enough here to score five out of five at two of the three tested speeds. Three shells cover XS–3XL.

Ninety degrees, and how the chin bar locks

Two things keep a modular chin bar working for years, and both are maintenance rather than design. Grit in the pivots is the first: after a wet, salted winter ride a rinse with clean water does more than any lubricant. The second is not forcing the bar past its stop when it is stiff — that is what bends the ratchet, and what turns a fifteen-euro part into a new chin bar. The ratchet system is available separately.

What ECE 22.06 and the P/J label mean

Worth a paragraph rather than a table row, because most shops leave it as one. The oblique test drops the helmet onto a slanted anvil faced with abrasive paper while instruments record how fast the head rotates, and compares that against the Brain Injury Criterion. It is the first time European regulation has limited the mechanism that does most of the damage in a real crash. The visor and every fitted accessory go through the process in place.

Twin Visor, sun visor — and the Pinlock that is not in the box

The visor aperture on a modular helmet has to seal against a chin bar that moves, which is a harder sealing problem than on a full-face and the reason cheap flip-ups whistle. Here the screen carries a scratch-resistant hardcoat, UV stabilisation against yellowing, and a quick-release mechanism designed to be worked at the roadside rather than on a bench.

Air, the breath deflector and the elastic-band liner

Everything that touches your head comes out and goes in a washing machine, and that is worth more than it sounds. A liner absorbs sweat and hair oils, and those break the foam down chemically as well as making the helmet smell. A liner washed twice a season lasts markedly longer than one that is never washed — and on this helmet the liner is a sixty-euro spare part rather than a reason to replace the whole thing.

1700 grams, no emergency release, and the rest of the honest list

1700 grams (±50), measured mid-size without accessories. Think of it as load rather than a number: your neck is not holding a helmet up, it is stabilising a mass on a lever every time the road moves. It is the lightest flip-up in our range and it is still around two hundred grams more than a comparable full-face — the unavoidable cost of a hinge, a latch and the reinforcement they need.

The other honest notes: no emergency release, no supplied Pinlock, and no published decibel figure, because none exists for this model and we will not manufacture one.

When something wears out

Seven visors are stocked for the Strobe II: clear, light tint, dark tint, three iridium mirrors and a rainbow. Worth planning as a pair rather than one at a time — a clear screen for winter and something tinted or mirrored for summer, swapped in a minute by the quick-release. Remember that the Pinlock is pinned to one visor and does not migrate between them.

In the box

• LS2 FF908 Strobe II helmet — Monza White Blue Red
• Carrying bag
• Reflective stickers
• 🔵 No Pinlock® insert — the visor is prepared for one (DKS520), sold separately

Specification

• Model — LS2 FF908 Strobe II
• Part number — 569082202
• Colour — Monza White Blue Red — Monza graphic, gloss white with blue and red
• Homologation — ECE 22.06, dual P/J (protective and jet)
• Safety rating — SHARP 4 of 5 stars (tested August 2026, ECE 22.06); chin bar fully locked in 37 % of impacts
• Helmet type — Flip-up / modular, chin bar raising 90° with locking system
• Shell — KPA (Kinetic Polymer Alloy), three shell sizes (XS–S / M–L / XL–3XL)
• Weight — 1700 g (±50 g)
• Sizes — XS to 3XL (seven sizes)
• Anti-fog — prepared for Pinlock® 70 MaxVision™ (DKS520) — insert NOT supplied
• Visor — Twin Visor System, scratch-resistant, UV-stable, quick-release
• Sun visor — integrated, tinted, drop-down
• Impact liner — multi-density EPS with moulded ventilation channels
• Retention — micrometric ratchet buckle, reinforced chin strap, chin bar lock
• Emergency release — not fitted on this model
• Ventilation — chin intake, top intake, rear exhaust port, breath deflector
• Liner — 3D laser-cut, elastic-band crown, hypoallergenic, breathable, removable and washable
• Intercom — prepared for the current LS2 Bluetooth system
• Serviceability — complete chin bar available as a spare part in every one of the twelve colourways