Leatt Knee&Shin Guard Dual Axis Grey – product view
⟲ 360° — drag me
From 850 g
02 · Data & docs

The facts.

Technical data
Product typeHard-shell knee and shin guard
CertificationEN 1621-1 Level 1 (knee and shin)
Leatt protection score25 points (manufacturer rating)
ConstructionHard shell over 3DF impact foam
HingeDual pivots on each side
Materials50% polypropylene, 25% polyurethane, 15% nylon, 5% polyester, 5% other
WeightFrom 850 g per pair (manufacturer)
SizesS/M, L/XL, XXL
ColourGrey/Black
DescriptionThe whole story▼

Grey plates with black details give this Leatt Dual Axis a lighter look than the all-black version, and the protection underneath is identical. From kneecap to shin, a hard shell sits on 3DF foam, and Leatt certifies both the knee and shin zones to EN 1621-1 Level 1.

If you ride motocross or enduro in boots and want the shin covered as well, the Dual Axis is built for that. Its hinge has two pivot points per side, so the guard moves with the knee rather than fighting it.

Key Features

  • CE certified for knee and shin, EN 1621-1 Level 1
  • 3DF impact foam beneath a hard shell
  • Two pivots per side copy the knee's natural motion
  • Slim shin plate slides into riding boots
  • Ventilation ports placed in critical areas
  • Rated 25 points on Leatt's own protection score
  • From 850 g per pair, according to Leatt

Covering knee and shin

A pure knee guard leaves the shin to the boot. The Dual Axis extends its protection down the front of the lower leg, and Leatt has the shin part certified too: knee and shin are tested as impact protection to EN 1621-1 at Level 1. The hard shell spreads the load of a strike, and the 3DF foam below takes the energy out of it.

Leatt gives this guard 25 points on its in-house scale. That is a manufacturer figure and useful mainly for comparing Leatt models.

Movement

Hinged guards with one pivot tend to push the plates out of place when the knee bends deeply. Leatt solves this with two pivots on each side, which follow the knee's natural path. Comfort on and off the bike improves because the guard does not lever against the leg when you crouch or stand.

Fit in the boot

The shin plate is deliberately slim so it fits inside riding boots without wedging them open. Leatt's data sheet describes dedicated left and right shapes and a strapping system that keeps the guards from slipping.

Airflow

Large ventilation ports sit in the areas that heat up most. A hard-shell guard needs that, especially on long summer motos.

Materials and sizes

Leatt's material list gives 50% polypropylene for the shell, 25% polyurethane for the foam, 15% nylon, 5% polyester and 5% other parts. Three sizes are offered: S/M, L/XL and XXL. Packaging is plastic-free.

Paperwork

The grey version shares its documents with the black one: Leatt's manual for the Dual Axis and an EU declaration of conformity issued through RICOTEST. Leatt lists the guard for motocross, enduro and trail.

Who the grey Dual Axis suits

Riders who wear light or colourful kits often find all-black plates too heavy-looking at the knee. The grey colourway answers that without any change to function: same certification for knee and shin, same twin-pivot hinge, same slim shin plate and the same S/M, L/XL and XXL sizing as the black version.

What you should know

The Dual Axis is heavier and bulkier than a soft knee sleeve, so check that it fits under your pants. It is certified at Level 1. Despite the hinges, it is a protector and not a knee brace; it gives no ligament support and does not limit hyperextension. Grey plates show dirt more readily than black ones, so expect to clean them more often if you want them to look fresh.

Colour

The grey and black colourway gives the Dual Axis a lighter, more technical appearance, which works well with light or multicoloured pants and kits. The grey plates make the shape of the guard more visible, while the black parts frame the hinges. Mud and dust show more on grey than on black, so a quick rinse after a wet ride keeps it looking sharp.

Specifications

Product type Hard-shell knee and shin guard
Certification EN 1621-1 Level 1 (knee and shin)
Leatt protection score 25 points (manufacturer rating)
Construction Hard shell over 3DF impact foam
Hinge Dual pivots on each side
Materials 50% polypropylene, 25% polyurethane, 15% nylon, 5% polyester, 5% other
Weight From 850 g per pair (manufacturer)
Sizes S/M, L/XL, XXL
Colour Grey/Black
DownloadsOwner's manual · brochure▼
07 · Support

Questions, one topic at a time.

Estimate your shipping

Get the real shipping cost for this item to your address — the same rates as checkout.

Pick your countrySame rates as checkout

Choose a destination and hit Estimate — we fetch the live rates for this item.

How long does delivery take?

We’re based in Germany. Standard delivery goes by DHL and national postal services and takes about 2–5 days within Germany, 1–2 weeks within the EU and 2–6 weeks outside the EU. Need it sooner? Express delivery reaches most of the world within a few days — just choose it at checkout where available.

How much does shipping cost?

Your exact shipping cost is calculated by destination and weight and shown at checkout before you pay — no hidden fees. Express delivery is selectable at checkout where available.

Do you ship to my country?

Yes, we ship to over 130 countries. Prices, taxes and delivery times for your destination are calculated automatically at checkout.

Will I have to pay customs or import duties?

Within the EU, no — our prices already include all duties and EU VAT. For deliveries outside the EU (e.g. Switzerland, the UK or the USA), your order may be subject to import duties and taxes set by your country. These are collected by the carrier when your parcel arrives, aren’t included in our prices, and are outside our control.

How can I track my order?

As soon as your parcel ships we email you a tracking link, so you can follow it all the way to your door.

What if an item is out of stock?

On out-of-stock items you can request a delivery time or leave your email to be notified the moment it returns — just use the notification box on the product.

Didn’t find your answer?

Our team will personally help you choose the right gear or part — around 24h for a reply.