{"title":"Suspension tubes \u0026 bodies","description":null,"products":[{"product_id":"ohlins-cylinder-head-36-26-m10-00201-029","title":"Öhlins Cylinder head 36\/26 M10 – 00201-029","description":"\u003cp\u003eCylinder head 36\/26 M10, Öhlins part number 00201-029. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eThread M10\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00201-029\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003e00201-029 is the 36 mm, 26 mm version — Öhlins lists each size separately. Öhlins machines the head so the bushing bore is concentric with the seal — otherwise the shaft wears one side. Surface finish is specified in microns, because it decides how quickly the piston band wears. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. Rebuilding to specification only works if the parts are to specification — that starts here. We can supply the whole position from the drawing rather than the single piece if that is easier. Service parts are supplied per piece unless the description says otherwise.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00201-029 in this case. diameter 36 mm, length 26 mm is what distinguishes this number from its neighbours in the range. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load. Most seal kits are built around a specific head design.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-029\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eThread:\u003c\/em\u003e M10\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646871036170,"sku":"00201-029","price":54.61,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-029_5c8a1994-1414-4d19-9178-c59a9c43e32b.png?v=1788868999"},{"product_id":"ohlins-cylinder-head-36-50-hose-m10-00201-10","title":"Öhlins Cylinder head 36\/50 hose M10 – 00201-10","description":"\u003cp\u003eCylinder head 36\/50 hose M10, Öhlins part number 00201-10. A head that has been over-tightened distorts and stops sealing.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 00201-10\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eThread M10\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 50 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eAt 36 mm, 50 mm it fits one position only; the next size up carries a different number. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. The tube is what the whole damper is built around: everything else references its bore. The cylinder head closes the working bore and carries the shaft seal and its bushing.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eSuspension is one of the few areas where the original part is genuinely the cheaper decision. Öhlins supports its suspension with individual service parts, which is why a fifteen-year-old damper can still be rebuilt to specification. Order by part number. The dimensions below are the ones Öhlins publishes for it. Ask us before ordering if you are unsure: a wrong part in a pressurised unit is an expensive lesson.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eOrder under 00201-10. Where several sizes share a description, only the number separates them. The published dimensions are diameter 36 mm, length 50 mm — measure the old part against them if you are unsure. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. Head and tube are matched by thread and diameter; neither is interchangeable across units.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eFitting service parts means opening a pressurised unit. As an authorised Öhlins service centre we do that here, with the right tools and a dyno check afterwards — just ask.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-10\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 50 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eThread:\u003c\/em\u003e M10\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646871167242,"sku":"00201-10","price":91.1,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-10_9ae95cd0-f887-402b-9efe-5593b73b8ed2.png?v=1788869002"},{"product_id":"ohlins-cylinder-head-36-22-gas-valve-00201-13","title":"Öhlins Cylinder head 36\/22 gas valve – 00201-13","description":"\u003cp\u003eCylinder head 36\/22 gas valve, Öhlins part number 00201-13. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 22 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00201-13\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eAt 36 mm, 22 mm it fits one position only; the next size up carries a different number. The cylinder head closes the working bore and carries the shaft seal and its bushing. Diameter and length together identify the tube — both are specific to the damper it came from. Head and tube are matched by thread and diameter; neither is interchangeable across units.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eThe part is identical to what Öhlins fits in production — same supplier, same specification. The tolerances here are the ones the unit was assembled to, not a pattern equivalent's interpretation of them. The exploded drawing for your unit names the number; if you do not have it, we do. Service parts are ordered per piece unless stated otherwise.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eOrder under 00201-13. Where several sizes share a description, only the number separates them. The published dimensions are diameter 36 mm, length 22 mm — measure the old part against them if you are unsure. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it. Most seal kits are built around a specific head design.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-13\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 22 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646871265546,"sku":"00201-13","price":104.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-13_6ce5b5e2-b02d-4435-8e8f-75eea00ebba6.png?v=1788869004"},{"product_id":"ohlins-cylinder-head-36-22-gas-valve-00201-17","title":"Öhlins Cylinder head 36\/22 gas valve – 00201-17","description":"\u003cp\u003eCylinder head 36\/22 gas valve, Öhlins part number 00201-17. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 00201-17\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 22 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eThis one measures 36 mm, 22 mm, and those figures are what separate it from the neighbouring numbers. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter. Head and tube are matched by thread and diameter; neither is interchangeable across units.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins supports its suspension with individual service parts, which is why a fifteen-year-old damper can still be rebuilt to specification. Öhlins is one of the few suspension makers that still supplies every position in the exploded view as a single part. If you are between two sizes, send us the measurement and we will check it against the catalogue. The exploded drawing for your unit names the number; if you do not have it, we do.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003e00201-17 is the Öhlins number for this position — the same one printed in the service documentation. The published dimensions are diameter 36 mm, length 22 mm — measure the old part against them if you are unsure. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-17\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 22 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646871363850,"sku":"00201-17","price":101.33,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-17_3a3581c7-8376-4e79-93b1-bf0c179a0da2.png?v=1788869007"},{"product_id":"ohlins-cylinder-head-36-22-hose-00201-21","title":"Öhlins Cylinder head 36\/22 hose – 00201-21","description":"\u003cp\u003eCylinder head 36\/22 hose, Öhlins part number 00201-21. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 22 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00201-21\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003e36 mm, 22 mm: that is the whole specification, and it has to match what came out. Öhlins machines the head so the bushing bore is concentric with the seal — otherwise the shaft wears one side. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eBuying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. Öhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. The Öhlins exploded view names the number for each position; we can look it up if you do not have it. We can supply the whole position from the drawing rather than the single piece if that is easier.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003ePart number 00201-21 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. Check diameter 36 mm, length 22 mm against what you have removed; a close size is not the same part. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. A head that has been over-tightened distorts and stops sealing.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-21\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 22 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646871462154,"sku":"00201-21","price":104.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-21_7437b7e7-ed14-42c6-82fc-aa48e92aae09.png?v=1788869009"},{"product_id":"ohlins-cylinder-head-36-pin-m10-type-d-00201-26","title":"Öhlins Cylinder head 36\/ pin M10 type D – 00201-26","description":"\u003cp\u003eCylinder head 36\/ pin M10 type D, Öhlins part number 00201-26. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThread M10\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00201-26\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThis one measures thread M10, and those figures are what separate it from the neighbouring numbers. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Twin-tube dampers use two concentric tubes, and both are listed separately. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eBuying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. This is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. If you are between two sizes, send us the measurement and we will check it against the catalogue. Service parts are supplied per piece unless the description says otherwise.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00201-26 in this case. The thread is M10. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-26\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eThread:\u003c\/em\u003e M10\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646871560458,"sku":"00201-26","price":104.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-26_5988000f-3ac4-4b55-b5f8-fd9ae166e52b.png?v=1788869012"},{"product_id":"ohlins-cylinder-head-36-26-hose-m10-00201-43","title":"Öhlins Cylinder head 36\/26 hose M10 – 00201-43","description":"\u003cp\u003eCylinder head 36\/26 hose M10, Öhlins part number 00201-43. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 00201-43\u003c\/li\u003e\n\u003cli\u003eThread M10\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eThe published figures are 36 mm, 26 mm. Measure the old part against them before ordering. Head and tube are matched by thread and diameter; neither is interchangeable across units. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eThe part number is the contract: it defines material, dimension and finish together. An original part keeps the unit within its published specification; a near-equivalent quietly moves it. Where a number has been superseded, Öhlins states the replacement — we pass that on. If the unit is already apart, compare the published dimensions with the part in your hand.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 00201-43. Öhlins states diameter 36 mm, length 26 mm for this number, and those figures are the deciding ones. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. Most seal kits are built around a specific head design.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00201-43\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eThread:\u003c\/em\u003e M10\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646872740106,"sku":"00201-43","price":104.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00201-43_586955cb-b44d-4975-84fa-f5e099141739.png?v=1788869018"},{"product_id":"ohlins-cylinder-tube-36-177-00300-01","title":"Öhlins Cylinder tube 36\/177 – 00300-01","description":"\u003cp\u003eCylinder tube 36\/177, Öhlins part number 00300-01. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 177 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-01\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eÖhlins gives it as 36 mm, 177 mm; nothing about that is approximate. Surface finish is specified in microns, because it decides how quickly the piston band wears. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eThe tolerances here are the ones the unit was assembled to, not a pattern equivalent's interpretation of them. The alternative to a service part is usually a new damper, which is why this catalogue exists. Tell us the damper's model designation and year and we will match the number for you. If you are between two sizes, send us the measurement and we will check it against the catalogue.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003e00300-01 is the Öhlins number for this position — the same one printed in the service documentation. Öhlins states diameter 36 mm, length 177 mm for this number, and those figures are the deciding ones. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-01\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 177 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646873854218,"sku":"00300-01","price":46.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-01_cd65582d-64d4-4268-af12-987643cc4179.png?v=1788869040"},{"product_id":"ohlins-cylinder-tube-36-207-00300-05","title":"Öhlins Cylinder tube 36\/207 – 00300-05","description":"\u003cp\u003eCylinder tube 36\/207, Öhlins part number 00300-05. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 207 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-05\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eDimensionally this is 36 mm, 207 mm, which is how it is told apart from the rest of the range. A hard bottoming often leaves a witness ring inside the bore — that tube is finished. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eThe alternative to a service part is usually a new damper, which is why this catalogue exists. Suspension is one of the few areas where the original part is genuinely the cheaper decision. We can supply the whole position from the drawing rather than the single piece if that is easier. If the unit is already apart, compare the published dimensions with the part in your hand.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 00300-05. The published dimensions are diameter 36 mm, length 207 mm — measure the old part against them if you are unsure. A hard bottoming often leaves a witness ring inside the bore — that tube is finished. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-05\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 207 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646873985290,"sku":"00300-05","price":75.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-05_7943a09a-2e4f-445f-83e1-48d08d704f1d.png?v=1788869043"},{"product_id":"ohlins-cylinder-tube-36-230-00300-07","title":"Öhlins Cylinder tube 36\/230 – 00300-07","description":"\u003cp\u003eCylinder tube 36\/230, Öhlins part number 00300-07. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 230 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-07\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eÖhlins gives it as 36 mm, 230 mm; nothing about that is approximate. The cylinder is one of the few damper parts that is genuinely wear-limited. The tube is what the whole damper is built around: everything else references its bore. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eThe part number is the contract: it defines material, dimension and finish together. The part is identical to what Öhlins fits in production — same supplier, same specification. The Öhlins exploded view names the number for each position; we can look it up if you do not have it. Order by part number — descriptions repeat across sizes, numbers do not.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003e00300-07 is the Öhlins number for this position — the same one printed in the service documentation. The published dimensions are diameter 36 mm, length 230 mm — measure the old part against them if you are unsure. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-07\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 230 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874083594,"sku":"00300-07","price":75.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-07_7a9a8380-cc22-4a14-a333-ef41e3359d3f.png?v=1788869046"},{"product_id":"ohlins-cylinder-tube-36-133-00300-12","title":"Öhlins Cylinder tube 36\/133 – 00300-12","description":"\u003cp\u003eCylinder tube 36\/133, Öhlins part number 00300-12. The tube also carries the end cap threads, so thread damage means a new tube.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 00300-12\u003c\/li\u003e\n\u003cli\u003eLength 133 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eThis one measures 36 mm, 133 mm, and those figures are what separate it from the neighbouring numbers. The tube also carries the end cap threads, so thread damage means a new tube. Surface finish is specified in microns, because it decides how quickly the piston band wears. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThe alternative to a service part is usually a new damper, which is why this catalogue exists. Öhlins keeps service parts available for units long after they leave the current price list. Service parts are ordered per piece unless stated otherwise. Where a number has been superseded, Öhlins states the replacement — we pass that on.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003e00300-12 is the Öhlins number for this position — the same one printed in the service documentation. Check diameter 36 mm, length 133 mm against what you have removed; a close size is not the same part. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-12\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 133 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874181898,"sku":"00300-12","price":37.76,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-12_ed0a0fb7-60e3-4f29-90df-bf8945409ea9.png?v=1788869049"},{"product_id":"ohlins-cylinder-tube-36-221-00300-19","title":"Öhlins Cylinder tube 36\/221 – 00300-19","description":"\u003cp\u003eCylinder tube 36\/221, Öhlins part number 00300-19. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 221 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-19\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThis one measures 36 mm, 221 mm, and those figures are what separate it from the neighbouring numbers. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins is one of the few suspension makers that still supplies every position in the exploded view as a single part. The alternative to a service part is usually a new damper, which is why this catalogue exists. If you are between two sizes, send us the measurement and we will check it against the catalogue. Order by part number — descriptions repeat across sizes, numbers do not.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00300-19 in this case. Öhlins states diameter 36 mm, length 221 mm for this number, and those figures are the deciding ones. The tube is what the whole damper is built around: everything else references its bore. Twin-tube dampers carry two concentric tubes and list them separately.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-19\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 221 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874280202,"sku":"00300-19","price":110.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-19_5b000e23-a54f-4b91-b326-0db99406254a.png?v=1788869051"},{"product_id":"ohlins-cylinder-tube-36-145-00300-24","title":"Öhlins Cylinder tube 36\/145 – 00300-24","description":"\u003cp\u003eCylinder tube 36\/145, Öhlins part number 00300-24. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 145 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-24\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eAt 36 mm, 145 mm it fits one position only; the next size up carries a different number. The tube is what the whole damper is built around: everything else references its bore. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Twin-tube dampers carry two concentric tubes and list them separately.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThe tolerances here are the ones the unit was assembled to, not a pattern equivalent's interpretation of them. Rebuilding to specification only works if the parts are to specification — that starts here. If you are between two sizes, send us the measurement and we will check it against the catalogue. For a full rebuild, the seal kit plus the wear parts is usually the sensible order.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eÖhlins identifies this position by the number 00300-24 in the exploded view for the unit it belongs to. Check diameter 36 mm, length 145 mm against what you have removed; a close size is not the same part. The tube also carries the end cap threads, so thread damage means a new tube. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-24\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 145 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874378506,"sku":"00300-24","price":47.02,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-24_82679018-7917-4857-ad08-a41bbc33e851.png?v=1788869054"},{"product_id":"ohlins-cylinder-tube-36-174-00300-26","title":"Öhlins Cylinder tube 36\/174 – 00300-26","description":"\u003cp\u003eCylinder tube 36\/174, Öhlins part number 00300-26. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-26\u003c\/li\u003e\n\u003cli\u003eLength 174 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eDimensionally this is 36 mm, 174 mm, which is how it is told apart from the rest of the range. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. The tube also carries the end cap threads, so thread damage means a new tube. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eThis is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. Suspension is one of the few areas where the original part is genuinely the cheaper decision. Service parts are ordered per piece unless stated otherwise. Service parts are supplied per piece unless the description says otherwise.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003ePart number 00300-26 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. The published dimensions are diameter 36 mm, length 174 mm — measure the old part against them if you are unsure. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-26\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 174 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874509578,"sku":"00300-26","price":46.48,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-26_72a9d2be-17d3-4f84-9013-cf14053e134a.png?v=1788869056"},{"product_id":"ohlins-cylinder-tube-36-171-00300-31","title":"Öhlins Cylinder tube 36\/171 – 00300-31","description":"\u003cp\u003eCylinder tube 36\/171, Öhlins part number 00300-31. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-31\u003c\/li\u003e\n\u003cli\u003eLength 171 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eÖhlins gives it as 36 mm, 171 mm; nothing about that is approximate. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eÖhlins publishes dimensions for its service parts so a workshop can verify before it fits. Suspension is one of the few areas where the original part is genuinely the cheaper decision. Where a number has been superseded, Öhlins states the replacement — we pass that on. For a full rebuild, the seal kit plus the wear parts is usually the sensible order.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 00300-31. diameter 36 mm, length 171 mm is what distinguishes this number from its neighbours in the range. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. A hard bottoming often leaves a witness ring inside the bore — that tube is finished.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-31\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 171 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874607882,"sku":"00300-31","price":39.8,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-31_bf3ff2e2-6efc-434f-b949-f95c2d1d24cf.png?v=1788869059"},{"product_id":"ohlins-cylinder-tube-36-242-00300-40","title":"Öhlins Cylinder tube 36\/242 – 00300-40","description":"\u003cp\u003eCylinder tube 36\/242, Öhlins part number 00300-40. A hard bottoming often leaves a witness ring inside the bore — that tube is finished.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 242 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00300-40\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eThe published figures are 36 mm, 242 mm. Measure the old part against them before ordering. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. Twin-tube dampers carry two concentric tubes and list them separately.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThis is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. Buying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. If you are between two sizes, send us the measurement and we will check it against the catalogue. We can supply the whole position from the drawing rather than the single piece if that is easier.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eÖhlins identifies this position by the number 00300-40 in the exploded view for the unit it belongs to. Check diameter 36 mm, length 242 mm against what you have removed; a close size is not the same part. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00300-40\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 242 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646874706186,"sku":"00300-40","price":43.81,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00300-40_d6b21921-05f9-45bc-9da3-a40f20af33fe.png?v=1788869062"},{"product_id":"ohlins-cylinder-head-pb-k36-25-00303-12","title":"Öhlins Cylinder head pb K36\/25 – 00303-12","description":"\u003cp\u003eCylinder head pb K36\/25, Öhlins part number 00303-12. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 25 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00303-12\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eDimensionally this is 36 mm, 25 mm, which is how it is told apart from the rest of the range. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Head and tube are matched by thread and diameter; neither is interchangeable across units. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. Öhlins keeps service parts available for units long after they leave the current price list. We can supply the whole position from the drawing rather than the single piece if that is easier. Send us the model and serial number of your unit and we will confirm the position before you order.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003e00303-12 is the Öhlins number for this position — the same one printed in the service documentation. The published dimensions are diameter 36 mm, length 25 mm — measure the old part against them if you are unsure. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00303-12\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 25 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646876213514,"sku":"00303-12","price":212.66,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00303-12_dd03d4fa-ebb1-4be2-be02-83ee6731ffeb.png?v=1788869083"},{"product_id":"ohlins-cylinder-head-pb-k36-22-00303-31","title":"Öhlins Cylinder head pb K36\/22 – 00303-31","description":"\u003cp\u003eCylinder head pb K36\/22, Öhlins part number 00303-31. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 22 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00303-31\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThis one measures 36 mm, 22 mm, and those figures are what separate it from the neighbouring numbers. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins supports its suspension with individual service parts, which is why a fifteen-year-old damper can still be rebuilt to specification. Öhlins publishes dimensions for its service parts so a workshop can verify before it fits. We can supply the whole position from the drawing rather than the single piece if that is easier. Order by part number — descriptions repeat across sizes, numbers do not.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003e00303-31 is the Öhlins number for this position — the same one printed in the service documentation. Öhlins states diameter 36 mm, length 22 mm for this number, and those figures are the deciding ones. Most seal kits are built around a specific head design. Head and tube are matched by thread and diameter; neither is interchangeable across units.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00303-31\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 22 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646876344586,"sku":"00303-31","price":191.61,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00303-31_070c34e2-7615-4efe-aa82-096806c3794c.png?v=1788869086"},{"product_id":"ohlins-cylinder-head-pb-90-36-22-00313-07","title":"Öhlins Cylinder head pb 90ø 36\/22 – 00313-07","description":"\u003cp\u003eCylinder head pb 90ø 36\/22, Öhlins part number 00313-07. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 36 mm\u003c\/li\u003e\n\u003cli\u003eLength 22 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00313-07\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eDimensionally this is 36 mm, 22 mm, which is how it is told apart from the rest of the range. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eBuying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. Öhlins publishes dimensions for its service parts so a workshop can verify before it fits. The Öhlins exploded view names the number for each position; we can look it up if you do not have it. We can supply the whole position from the drawing rather than the single piece if that is easier.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 00313-07. Öhlins states diameter 36 mm, length 22 mm for this number, and those figures are the deciding ones. The tube is what the whole damper is built around: everything else references its bore. Head and tube are matched by thread and diameter; neither is interchangeable across units.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00313-07\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 36 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 22 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646880833802,"sku":"00313-07","price":172.74,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00313-07_61bc65f3-e0c7-4386-9adc-d0847e54d1d1.png?v=1788869094"},{"product_id":"ohlins-cylinder-head-46-00515-02","title":"Öhlins Cylinder head 46 – 00515-02","description":"\u003cp\u003eCylinder head 46, Öhlins part number 00515-02. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00515-02\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThis position is identified by its number rather than by a dimension. Head and tube are matched by thread and diameter; neither is interchangeable across units. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThe part number is the contract: it defines material, dimension and finish together. Every part in this catalogue is one Öhlins fits itself during assembly and service. If the unit is already apart, compare the published dimensions with the part in your hand. Öhlins numbers do not follow a logic you can guess — always read them from the documentation.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eOrder under 00515-02. Where several sizes share a description, only the number separates them. Öhlins does not publish a dimension here — go by the number and the exploded view. The tube is what the whole damper is built around: everything else references its bore. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eFitting service parts means opening a pressurised unit. As an authorised Öhlins service centre we do that here, with the right tools and a dyno check afterwards — just ask.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00515-02\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53646904819978,"sku":"00515-02","price":232.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00515-02_1e86fbc7-d164-4167-97f2-4b477ac02242.png?v=1788869471"},{"product_id":"ohlins-cylinder-head-90-pb-46-26-00870-53","title":"Öhlins Cylinder head 90ø pb 46\/26 – 00870-53","description":"\u003cp\u003eCylinder head 90ø pb 46\/26, Öhlins part number 00870-53. Head and tube are matched by thread and diameter; neither is interchangeable across units.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00870-53\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003e00870-53 is the 46 mm, 26 mm version — Öhlins lists each size separately. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse. Surface finish is specified in microns, because it decides how quickly the piston band wears. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins lists this part under its own number in the service catalogue so a workshop can order exactly what it needs. This is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. Tell us the damper's model designation and year and we will match the number for you. Order by part number — descriptions repeat across sizes, numbers do not.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 00870-53. Check diameter 46 mm, length 26 mm against what you have removed; a close size is not the same part. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00870-53\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647920267530,"sku":"00870-53","price":379.69,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00870-53_fdf73463-b680-40fa-86b6-32c5641399ed.png?v=1788870214"},{"product_id":"ohlins-cylinder-head-19-pb-46-26-00870-58","title":"Öhlins Cylinder head 19ø pb 46\/26 – 00870-58","description":"\u003cp\u003eCylinder head 19ø pb 46\/26, Öhlins part number 00870-58. It is the part that keeps oil in and grit out, which is why it is replaced whenever the unit weeps.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00870-58\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eÖhlins publishes 46 mm, 26 mm for 00870-58 — the dimensions are the identity of the part. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eParts remain available years after a unit leaves the current price list, which is unusual in this trade. The part number is the contract: it defines material, dimension and finish together. Ask us before ordering if you are unsure: a wrong part in a pressurised unit is an expensive lesson. Send us the model and serial number of your unit and we will confirm the position before you order.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00870-58 in this case. The published dimensions are diameter 46 mm, length 26 mm — measure the old part against them if you are unsure. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00870-58\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647920922890,"sku":"00870-58","price":290.87,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00870-58_ffc1e9c8-656b-4c69-9b79-8be7094cdf91.png?v=1788870216"},{"product_id":"ohlins-cylinder-head-115-10-pb-46-26-00870-68","title":"Öhlins Cylinder head 115°\/10° pb 46\/26 – 00870-68","description":"\u003cp\u003eCylinder head 115°\/10° pb 46\/26, Öhlins part number 00870-68. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00870-68\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 26 mm it fits one position only; the next size up carries a different number. Diameter and length together identify the tube — both are specific to the damper it came from. Head and tube are matched by thread and diameter; neither is interchangeable across units. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThe alternative to a service part is usually a new damper, which is why this catalogue exists. Öhlins is one of the few suspension makers that still supplies every position in the exploded view as a single part. If you are between two sizes, send us the measurement and we will check it against the catalogue. For a full rebuild, the seal kit plus the wear parts is usually the sensible order.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 00870-68. Check diameter 46 mm, length 26 mm against what you have removed; a close size is not the same part. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eFitting service parts means opening a pressurised unit. As an authorised Öhlins service centre we do that here, with the right tools and a dyno check afterwards — just ask.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00870-68\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647924265226,"sku":"00870-68","price":333.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00870-68_27507211-1cb8-40f0-8021-613dbdfb70a4.png?v=1788870218"},{"product_id":"ohlins-cylinder-head-0-pb-46-26-00870-71","title":"Öhlins Cylinder head 0° pb 46\/26 – 00870-71","description":"\u003cp\u003eCylinder head 0° pb 46\/26, Öhlins part number 00870-71. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00870-71\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003e00870-71 is the 46 mm, 26 mm version — Öhlins lists each size separately. A head that has been over-tightened distorts and stops sealing. Öhlins machines the head so the bushing bore is concentric with the seal — otherwise the shaft wears one side. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThis is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. Öhlins numbers every position so a workshop can order precisely what it needs, not a whole assembly. Öhlins numbers do not follow a logic you can guess — always read them from the documentation. If the unit is already apart, compare the published dimensions with the part in your hand.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003ePart number 00870-71 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. Check diameter 46 mm, length 26 mm against what you have removed; a close size is not the same part. Twin-tube dampers use two concentric tubes, and both are listed separately. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00870-71\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647928492298,"sku":"00870-71","price":290.87,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00870-71_97771830-ae09-4236-8524-12ef172f47e3.png?v=1788870221"},{"product_id":"ohlins-cylinder-head-90-pb-46-26-bob-r-00870-92","title":"Öhlins Cylinder head 90° pb 46\/26 BOB-R – 00870-92","description":"\u003cp\u003eCylinder head 90° pb 46\/26 BOB-R, Öhlins part number 00870-92. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00870-92\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eÖhlins publishes 46 mm, 26 mm for 00870-92 — the dimensions are the identity of the part. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston. A head that has been over-tightened distorts and stops sealing.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eA damper that can be rebuilt is a damper that stays on the bike; that is the whole argument for original service parts. Rebuilding to specification only works if the parts are to specification — that starts here. We can check the number against the Öhlins exploded view before you order — just ask. Öhlins parts are unit-specific: a close dimension is not a substitute.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00870-92 in this case. Öhlins states diameter 46 mm, length 26 mm for this number, and those figures are the deciding ones. A head that has been over-tightened distorts and stops sealing. Öhlins machines the head so the bushing bore is concentric with the seal — otherwise the shaft wears one side.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00870-92\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647931605258,"sku":"00870-92","price":205.33,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00870-92_77c4aec4-fc19-40d7-b47d-d8628fcc77e7.png?v=1788870223"},{"product_id":"ohlins-cylinder-head-90-pb-6-26-00880-53","title":"Öhlins Cylinder head 90ø pb 6\/26 – 00880-53","description":"\u003cp\u003eCylinder head 90ø pb 6\/26, Öhlins part number 00880-53. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 00880-53\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 6 mm\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eÖhlins gives it as 6 mm, 26 mm; nothing about that is approximate. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eEvery part in this catalogue is one Öhlins fits itself during assembly and service. An original part keeps the unit within its published specification; a near-equivalent quietly moves it. Service parts are supplied per piece unless the description says otherwise. If you are unsure which number your unit takes, send us the model and serial number of the damper and we will look it up.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eOrder under 00880-53. Where several sizes share a description, only the number separates them. The published dimensions are diameter 6 mm, length 26 mm — measure the old part against them if you are unsure. The tube is what the whole damper is built around: everything else references its bore. A head that has been over-tightened distorts and stops sealing.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eA damper rebuild is workshop work: it needs the unit dismantled, the shim stack rebuilt in the correct order and the gas charge reset. We are an authorised Öhlins service centre and do exactly that in house — send us the unit or ask us to fit the part with your order.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00880-53\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 6 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647934423306,"sku":"00880-53","price":204.56,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00880-53_ec8230f4-37a6-4355-b01d-b04b275f325a.png?v=1788870226"},{"product_id":"ohlins-cylinder-head-30-pb-46-26-00880-60","title":"Öhlins Cylinder head 30° PB 46\/26 – 00880-60","description":"\u003cp\u003eCylinder head 30° PB 46\/26, Öhlins part number 00880-60. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00880-60\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eDimensionally this is 46 mm, 26 mm, which is how it is told apart from the rest of the range. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins keeps service parts available for units long after they leave the current price list. Rebuilding to specification only works if the parts are to specification — that starts here. Where a number has been superseded, Öhlins states the replacement — we pass that on. We can supply the whole position from the drawing rather than the single piece if that is easier.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003e00880-60 is the Öhlins number for this position — the same one printed in the service documentation. Check diameter 46 mm, length 26 mm against what you have removed; a close size is not the same part. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00880-60\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647937569034,"sku":"00880-60","price":211.04,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00880-60_c3036f58-ae5e-4a40-bab4-5cdaa6a184ad.png?v=1788870228"},{"product_id":"ohlins-cylinder-head-110-pb-46-26-00880-69","title":"Öhlins Cylinder head 110° PB 46\/26 – 00880-69","description":"\u003cp\u003eCylinder head 110° PB 46\/26, Öhlins part number 00880-69. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00880-69\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThe published figures are 46 mm, 26 mm. Measure the old part against them before ordering. Öhlins machines the head so the bushing bore is concentric with the seal — otherwise the shaft wears one side. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins lists this part under its own number in the service catalogue so a workshop can order exactly what it needs. The tolerances here are the ones the unit was assembled to, not a pattern equivalent's interpretation of them. Order by part number — descriptions repeat across sizes, numbers do not. We can check the number against the Öhlins exploded view before you order — just ask.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eÖhlins identifies this position by the number 00880-69 in the exploded view for the unit it belongs to. diameter 46 mm, length 26 mm is what distinguishes this number from its neighbours in the range. Most seal kits are built around a specific head design. Öhlins machines the head so the bushing bore is concentric with the seal — otherwise the shaft wears one side.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00880-69\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647941337354,"sku":"00880-69","price":223.88,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00880-69_13c5113d-4e0a-4805-b108-afa2689f34e7.png?v=1788870233"},{"product_id":"ohlins-cylinder-head-blank-00880-87","title":"Öhlins Cylinder head blank – 00880-87","description":"\u003cp\u003eCylinder head blank, Öhlins part number 00880-87. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00880-87\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eThis position is identified by its number rather than by a dimension. It is the part that keeps oil in and grit out, which is why it is replaced whenever the unit weeps. Surface finish is specified in microns, because it decides how quickly the piston band wears. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eBuying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. Öhlins manufactures service parts on the same lines as production parts — there is no second quality. If you are between two sizes, send us the measurement and we will check it against the catalogue. Öhlins numbers do not follow a logic you can guess — always read them from the documentation.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00880-87 in this case. This position has no published dimension, so the part number is the only reliable identifier. It is the part that keeps oil in and grit out, which is why it is replaced whenever the unit weeps. Most seal kits are built around a specific head design.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00880-87\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647942779146,"sku":"00880-87","price":72.85,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00880-87_2b593aaf-b28a-4ad7-baba-089c5050c2f6.png?v=1788870235"},{"product_id":"ohlins-cylinder-head-342-5-pb-46-26-00890-54","title":"Öhlins Cylinder head 342.5ø pb 46\/26 – 00890-54","description":"\u003cp\u003eCylinder head 342.5ø pb 46\/26, Öhlins part number 00890-54. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00890-54\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003e46 mm, 26 mm: that is the whole specification, and it has to match what came out. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eÖhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. Buying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. We can check the number against the Öhlins exploded view before you order — just ask. Tell us the damper's model designation and year and we will match the number for you.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 00890-54 in this case. The published dimensions are diameter 46 mm, length 26 mm — measure the old part against them if you are unsure. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00890-54\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647956934922,"sku":"00890-54","price":209.57,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00890-54_cde78b18-b7de-4cda-a72f-dc47d6cf28ba.png?v=1788870244"},{"product_id":"ohlins-cylinder-head-20-pb-46-26-00890-57","title":"Öhlins Cylinder head 20ø pb 46\/26 – 00890-57","description":"\u003cp\u003eCylinder head 20ø pb 46\/26, Öhlins part number 00890-57. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 26 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 00890-57\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 26 mm it fits one position only; the next size up carries a different number. The cylinder head closes the working bore and carries the shaft seal and its bushing. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eThe tolerances here are the ones the unit was assembled to, not a pattern equivalent's interpretation of them. This is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. Tell us the damper's model designation and year and we will match the number for you. If the unit is already apart, compare the published dimensions with the part in your hand.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eOrder under 00890-57. Where several sizes share a description, only the number separates them. The published dimensions are diameter 46 mm, length 26 mm — measure the old part against them if you are unsure. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 00890-57\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 26 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647960670474,"sku":"00890-57","price":273.31,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/00890-57_f1f2ade8-cb35-4906-a392-0d1e06a93913.png?v=1788870247"},{"product_id":"ohlins-cylinder-tube-46-167-5-01010-02","title":"Öhlins Cylinder tube 46\/167.5 – 01010-02","description":"\u003cp\u003eCylinder tube 46\/167.5, Öhlins part number 01010-02. The tube also carries the end cap threads, so thread damage means a new tube.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 167.5 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-02\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 167.5 mm it fits one position only; the next size up carries a different number. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. The tube is what the whole damper is built around: everything else references its bore. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins lists this part under its own number in the service catalogue so a workshop can order exactly what it needs. Öhlins keeps service parts available for units long after they leave the current price list. Order by part number. The dimensions below are the ones Öhlins publishes for it. If the unit is already apart, compare the published dimensions with the part in your hand.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 01010-02 in this case. The published dimensions are diameter 46 mm, length 167.5 mm — measure the old part against them if you are unsure. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-02\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 167.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647970140426,"sku":"01010-02","price":103.78,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-02_5a7fc494-29cb-488b-8c69-8b2989d20b36.png?v=1788870255"},{"product_id":"ohlins-cylinder-tube-46-123-5-01010-05","title":"Öhlins Cylinder tube 46\/123.5 – 01010-05","description":"\u003cp\u003eCylinder tube 46\/123.5, Öhlins part number 01010-05. A hard bottoming often leaves a witness ring inside the bore — that tube is finished.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-05\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eLength 123.5 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003e01010-05 is the 46 mm, 123.5 mm version — Öhlins lists each size separately. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins numbers every position so a workshop can order precisely what it needs, not a whole assembly. Suspension is one of the few areas where the original part is genuinely the cheaper decision. Order by part number — descriptions repeat across sizes, numbers do not. We can supply the whole position from the drawing rather than the single piece if that is easier.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 01010-05. diameter 46 mm, length 123.5 mm is what distinguishes this number from its neighbours in the range. The cylinder is one of the few damper parts that is genuinely wear-limited. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-05\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 123.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647973351690,"sku":"01010-05","price":54.49,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-05_bce0db5a-4c46-4378-8b27-6037a13a95d7.png?v=1788870257"},{"product_id":"ohlins-cylinder-tube-46-194-5-01010-07","title":"Öhlins Cylinder tube 46\/194.5 – 01010-07","description":"\u003cp\u003eCylinder tube 46\/194.5, Öhlins part number 01010-07. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-07\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eLength 194.5 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eÖhlins gives it as 46 mm, 194.5 mm; nothing about that is approximate. The cylinder is one of the few damper parts that is genuinely wear-limited. Twin-tube dampers use two concentric tubes, and both are listed separately. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eA damper that can be rebuilt is a damper that stays on the bike; that is the whole argument for original service parts. Öhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. We can supply the whole position from the drawing rather than the single piece if that is easier. Service parts are ordered per piece unless stated otherwise.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003ePart number 01010-07 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. Öhlins states diameter 46 mm, length 194.5 mm for this number, and those figures are the deciding ones. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-07\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 194.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647975710986,"sku":"01010-07","price":76.91,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-07_a57565aa-4356-4eae-8830-5eada2447afe.png?v=1788870260"},{"product_id":"ohlins-cylinder-tube-46-137-01010-09","title":"Öhlins Cylinder tube 46\/137 – 01010-09","description":"\u003cp\u003eCylinder tube 46\/137, Öhlins part number 01010-09. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 137 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-09\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eÖhlins publishes 46 mm, 137 mm for 01010-09 — the dimensions are the identity of the part. Surface finish is specified in microns, because it decides how quickly the piston band wears. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eRebuilding to specification only works if the parts are to specification — that starts here. Suspension is one of the few areas where the original part is genuinely the cheaper decision. If you are unsure which number your unit takes, send us the model and serial number of the damper and we will look it up. Order by part number. The dimensions below are the ones Öhlins publishes for it.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 01010-09 in this case. The published dimensions are diameter 46 mm, length 137 mm — measure the old part against them if you are unsure. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-09\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 137 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647979970826,"sku":"01010-09","price":117.51,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-09_1bfe76da-3593-495d-b440-53c59cac3efd.png?v=1788870262"},{"product_id":"ohlins-cylinder-tube-46-212-5-01010-14","title":"Öhlins Cylinder tube 46\/212.5 – 01010-14","description":"\u003cp\u003eCylinder tube 46\/212.5, Öhlins part number 01010-14. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-14\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eLength 212.5 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003e01010-14 is the 46 mm, 212.5 mm version — Öhlins lists each size separately. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eÖhlins lists this part under its own number in the service catalogue so a workshop can order exactly what it needs. Öhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. Send us the model and serial number of your unit and we will confirm the position before you order. Order by part number. The dimensions below are the ones Öhlins publishes for it.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003e01010-14 is the Öhlins number for this position — the same one printed in the service documentation. Öhlins states diameter 46 mm, length 212.5 mm for this number, and those figures are the deciding ones. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eFitting service parts means opening a pressurised unit. As an authorised Öhlins service centre we do that here, with the right tools and a dyno check afterwards — just ask.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-14\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 212.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647980200202,"sku":"01010-14","price":117.69,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-14_539ddccd-8d25-4c6a-b5cd-d1d168f1d382.png?v=1788870267"},{"product_id":"ohlins-cylinder-tube-46-274-spc-01010-21","title":"Öhlins Cylinder tube 46\/274 spc – 01010-21","description":"\u003cp\u003eCylinder tube 46\/274 spc, Öhlins part number 01010-21. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 274 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-21\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 274 mm it fits one position only; the next size up carries a different number. Twin-tube dampers carry two concentric tubes and list them separately. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eÖhlins is one of the few suspension makers that still supplies every position in the exploded view as a single part. Öhlins keeps service parts available for units long after they leave the current price list. Ask us before ordering if you are unsure: a wrong part in a pressurised unit is an expensive lesson. Öhlins parts are unit-specific: a close dimension is not a substitute.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 01010-21 in this case. diameter 46 mm, length 274 mm is what distinguishes this number from its neighbours in the range. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eA damper rebuild is workshop work: it needs the unit dismantled, the shim stack rebuilt in the correct order and the gas charge reset. We are an authorised Öhlins service centre and do exactly that in house — send us the unit or ask us to fit the part with your order.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-21\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 274 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647985705226,"sku":"01010-21","price":144.01,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-21_90eb13ca-9cee-4238-9809-43a2ba837972.png?v=1788870268"},{"product_id":"ohlins-cylinder-tube-46-198-01010-23","title":"Öhlins Cylinder tube 46\/198 – 01010-23","description":"\u003cp\u003eCylinder tube 46\/198, Öhlins part number 01010-23. Öhlins hones its tubes to a defined surface finish rather than simply to a diameter.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-23\u003c\/li\u003e\n\u003cli\u003eLength 198 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003e01010-23 is the 46 mm, 198 mm version — Öhlins lists each size separately. Surface finish is specified in microns, because it decides how quickly the piston band wears. Twin-tube dampers use two concentric tubes, and both are listed separately. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eÖhlins supports its suspension with individual service parts, which is why a fifteen-year-old damper can still be rebuilt to specification. An original part keeps the unit within its published specification; a near-equivalent quietly moves it. For a full rebuild, the seal kit plus the wear parts is usually the sensible order. The Öhlins exploded view names the number for each position; we can look it up if you do not have it.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 01010-23. Check diameter 46 mm, length 198 mm against what you have removed; a close size is not the same part. A hard bottoming often leaves a witness ring inside the bore — that tube is finished. Diameter and length together identify the tube — both are specific to the damper it came from.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-23\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 198 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647988490506,"sku":"01010-23","price":136.15,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-23_d323f1b1-9891-416a-b05d-9377b3871da2.png?v=1788870270"},{"product_id":"ohlins-cylinder-tube-46-200-01010-25","title":"Öhlins Cylinder tube 46\/200 – 01010-25","description":"\u003cp\u003eCylinder tube 46\/200, Öhlins part number 01010-25. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-25\u003c\/li\u003e\n\u003cli\u003eLength 200 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eThe published figures are 46 mm, 200 mm. Measure the old part against them before ordering. Diameter and length together identify the tube — both are specific to the damper it came from. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eA damper that can be rebuilt is a damper that stays on the bike; that is the whole argument for original service parts. This is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. If you are unsure which number your unit takes, send us the model and serial number of the damper and we will look it up. If you are between two sizes, send us the measurement and we will check it against the catalogue.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003e01010-25 is the Öhlins number for this position — the same one printed in the service documentation. The published dimensions are diameter 46 mm, length 200 mm — measure the old part against them if you are unsure. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-25\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 200 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647993045258,"sku":"01010-25","price":136.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-25_5c4cb01f-d8ac-44b3-8a95-514f03f40599.png?v=1788870273"},{"product_id":"ohlins-cylinder-tube-46-224-01010-28","title":"Öhlins Cylinder tube 46\/224 – 01010-28","description":"\u003cp\u003eCylinder tube 46\/224, Öhlins part number 01010-28. The tube is what the whole damper is built around: everything else references its bore.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 224 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-28\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 224 mm it fits one position only; the next size up carries a different number. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eParts remain available years after a unit leaves the current price list, which is unusual in this trade. Öhlins manufactures service parts on the same lines as production parts — there is no second quality. Ask us before ordering if you are unsure: a wrong part in a pressurised unit is an expensive lesson. If you are unsure which number your unit takes, send us the model and serial number of the damper and we will look it up.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 01010-28. Check diameter 46 mm, length 224 mm against what you have removed; a close size is not the same part. Twin-tube dampers carry two concentric tubes and list them separately. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-28\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 224 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647995633930,"sku":"01010-28","price":119.29,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-28_5ee9fa09-6f8e-43f9-86be-dc6575a418e2.png?v=1788870275"},{"product_id":"ohlins-cylinder-tube-46-215-5-01010-31","title":"Öhlins Cylinder tube 46\/215.5 – 01010-31","description":"\u003cp\u003eCylinder tube 46\/215.5, Öhlins part number 01010-31. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-31\u003c\/li\u003e\n\u003cli\u003eLength 215.5 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 215.5 mm it fits one position only; the next size up carries a different number. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against. The cylinder tube is the working bore of the damper: the piston runs in it, and its finish decides how well the piston rings seal. The tube also carries the end cap threads, so thread damage means a new tube.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eParts remain available years after a unit leaves the current price list, which is unusual in this trade. Öhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. If you are between two sizes, send us the measurement and we will check it against the catalogue. If the unit is already apart, compare the published dimensions with the part in your hand.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003e01010-31 is the Öhlins number for this position — the same one printed in the service documentation. Check diameter 46 mm, length 215.5 mm against what you have removed; a close size is not the same part. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-31\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 215.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647998648586,"sku":"01010-31","price":78.49,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-31_86e68cac-8e32-4971-9c16-f9091a2c6ab6.png?v=1788870278"},{"product_id":"ohlins-cylinder-tube-46-181-5-01010-34","title":"Öhlins Cylinder tube 46\/181.5 – 01010-34","description":"\u003cp\u003eCylinder tube 46\/181.5, Öhlins part number 01010-34. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-34\u003c\/li\u003e\n\u003cli\u003eLength 181.5 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003e46 mm, 181.5 mm: that is the whole specification, and it has to match what came out. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins lists this part under its own number in the service catalogue so a workshop can order exactly what it needs. The part is identical to what Öhlins fits in production — same supplier, same specification. Service parts are supplied per piece unless the description says otherwise. If you are between two sizes, send us the measurement and we will check it against the catalogue.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003ePart number 01010-34 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. Check diameter 46 mm, length 181.5 mm against what you have removed; a close size is not the same part. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eÖhlins recommends that its units are serviced by an authorised centre. We are one: rebuild, revalve and setup all happen in our own workshop.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-34\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 181.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53647999271178,"sku":"01010-34","price":132.76,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-34_c17d889d-85eb-41a5-b629-0e86cc4111c7.png?v=1788870280"},{"product_id":"ohlins-cylinder-tube-46-266-01010-37","title":"Öhlins Cylinder tube 46\/266 – 01010-37","description":"\u003cp\u003eCylinder tube 46\/266, Öhlins part number 01010-37. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLength 266 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-37\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 266 mm it fits one position only; the next size up carries a different number. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eThe part is identical to what Öhlins fits in production — same supplier, same specification. Öhlins is one of the few suspension makers that still supplies every position in the exploded view as a single part. Order by part number — descriptions repeat across sizes, numbers do not. The Öhlins exploded view names the number for each position; we can look it up if you do not have it.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003ePart number 01010-37 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. Check diameter 46 mm, length 266 mm against what you have removed; a close size is not the same part. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-37\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 266 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648006447370,"sku":"01010-37","price":96.94,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-37_6f65118b-4266-44c4-bf03-9c1675024059.png?v=1788870283"},{"product_id":"ohlins-cylinder-tube-46-163-01010-40","title":"Öhlins Cylinder tube 46\/163 – 01010-40","description":"\u003cp\u003eCylinder tube 46\/163, Öhlins part number 01010-40. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-40\u003c\/li\u003e\n\u003cli\u003eLength 163 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThis one measures 46 mm, 163 mm, and those figures are what separate it from the neighbouring numbers. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eSuspension is one of the few areas where the original part is genuinely the cheaper decision. An original part keeps the unit within its published specification; a near-equivalent quietly moves it. Service parts are supplied per piece unless the description says otherwise. We can check the number against the Öhlins exploded view before you order — just ask.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 01010-40. Öhlins states diameter 46 mm, length 163 mm for this number, and those figures are the deciding ones. Diameter and length together identify the tube — both are specific to the damper it came from. Surface finish is specified in microns, because it decides how quickly the piston band wears.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-40\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 163 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648010215690,"sku":"01010-40","price":127.94,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-40_06fa789a-ab63-41d5-bc8f-546dffc2c89c.png?v=1788870285"},{"product_id":"ohlins-cylinder-tube-46-220-5-01010-43","title":"Öhlins Cylinder tube 46\/220.5 – 01010-43","description":"\u003cp\u003eCylinder tube 46\/220.5, Öhlins part number 01010-43. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 220.5 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-43\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003eÖhlins gives it as 46 mm, 220.5 mm; nothing about that is approximate. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins manufactures service parts on the same lines as production parts — there is no second quality. The part number is the contract: it defines material, dimension and finish together. If you are unsure which number your unit takes, send us the model and serial number of the damper and we will look it up. We can check the number against the Öhlins exploded view before you order — just ask.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003ePart number 01010-43 is unambiguous; the description alone is not, because Öhlins uses similar wording across sizes. Check diameter 46 mm, length 220.5 mm against what you have removed; a close size is not the same part. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-43\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 220.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648014803210,"sku":"01010-43","price":118.78,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-43_24ce507b-81cc-42af-baa8-3f0fabac1617.png?v=1788870288"},{"product_id":"ohlins-cylinder-tube-46-270-01010-47","title":"Öhlins Cylinder tube 46\/270 – 01010-47","description":"\u003cp\u003eCylinder tube 46\/270, Öhlins part number 01010-47. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 270 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-47\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003e01010-47 is the 46 mm, 270 mm version — Öhlins lists each size separately. Reservoir tubes carry the gas charge and are built to the same standard as the working cylinder. The tube is what the whole damper is built around: everything else references its bore. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eAn original part keeps the unit within its published specification; a near-equivalent quietly moves it. Rebuilding to specification only works if the parts are to specification — that starts here. We can check the number against the Öhlins exploded view before you order — just ask. The exploded drawing for your unit names the number; if you do not have it, we do.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 01010-47 in this case. The published dimensions are diameter 46 mm, length 270 mm — measure the old part against them if you are unsure. A scored bore means lost damping, because the oil bypasses the piston rather than being forced through the shims. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-47\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 270 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648015098122,"sku":"01010-47","price":104.14,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-47_a54e9eed-f2b0-468f-b63d-602b1b2a64a6.png?v=1788870290"},{"product_id":"ohlins-cylinder-tube-46-171-5-01010-52","title":"Öhlins Cylinder tube 46\/171.5 – 01010-52","description":"\u003cp\u003eCylinder tube 46\/171.5, Öhlins part number 01010-52. The tube also carries the end cap threads, so thread damage means a new tube.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eLength 171.5 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-52\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFunction\u003c\/h2\u003e\u003cp\u003eThis one measures 46 mm, 171.5 mm, and those figures are what separate it from the neighbouring numbers. Wall thickness and bore finish are what let a cylinder hold pressure without deforming under load. Diameter and length together identify the tube — both are specific to the damper it came from. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins supports units that are decades old, which is why the spare parts list runs to thousands of numbers. This is an original Öhlins part, not an aftermarket equivalent — the tolerances are the ones the unit was assembled to. Öhlins parts are unit-specific: a close dimension is not a substitute. Order by part number. The dimensions below are the ones Öhlins publishes for it.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eÖhlins identifies this position by the number 01010-52 in the exploded view for the unit it belongs to. The published dimensions are diameter 46 mm, length 171.5 mm — measure the old part against them if you are unsure. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-52\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 171.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648018145546,"sku":"01010-52","price":107.6,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-52_5ae83c08-998e-41e1-a2b9-f196a10bbecc.png?v=1788870293"},{"product_id":"ohlins-cylinder-tube-46-293-01010-55","title":"Öhlins Cylinder tube 46\/293 – 01010-55","description":"\u003cp\u003eCylinder tube 46\/293, Öhlins part number 01010-55. Twin-tube dampers use two concentric tubes, and both are listed separately.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eLength 293 mm\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-55\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Is\u003c\/h2\u003e\u003cp\u003e46 mm, 293 mm: that is the whole specification, and it has to match what came out. The tube carries the end cap threads, so damaged threads mean a new tube rather than a repair. Bore finish decides how well the piston band seals; a scored tube leaks damping past the piston. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit.\u003c\/p\u003e\u003ch2\u003eGenuine Service Part\u003c\/h2\u003e\u003cp\u003eBuying the individual part rather than a complete assembly is what makes servicing an Öhlins unit worthwhile. The tolerances here are the ones the unit was assembled to, not a pattern equivalent's interpretation of them. Öhlins numbers do not follow a logic you can guess — always read them from the documentation. Where a number has been superseded, Öhlins states the replacement — we pass that on.\u003c\/p\u003e\u003ch2\u003eHow to Be Sure It Fits\u003c\/h2\u003e\u003cp\u003eThe reliable route is the exploded drawing: find the position, read the number, order it — 01010-55 in this case. diameter 46 mm, length 293 mm is what distinguishes this number from its neighbours in the range. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eAsk us about a full service: as an authorised Öhlins centre we strip, inspect, replace what is worn and set the unit back to its specification.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-55\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 293 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648019915018,"sku":"01010-55","price":119.87,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-55_835b8507-6a50-4037-bebf-9fe2dc180a02.png?v=1788870295"},{"product_id":"ohlins-cylinder-tube-46-321-01010-61","title":"Öhlins Cylinder tube 46\/321 – 01010-61","description":"\u003cp\u003eCylinder tube 46\/321, Öhlins part number 01010-61. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003cli\u003eÖhlins part number 01010-61\u003c\/li\u003e\n\u003cli\u003eLength 321 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003eAt 46 mm, 321 mm it fits one position only; the next size up carries a different number. Tubes are replaced when the bore is marked; polishing them out changes the clearance and makes it worse. Öhlins matches tube and piston as a pair during assembly, which is why the part numbers are specific. Corrosion inside a tube is terminal: it cannot be honed out without changing the clearance.\u003c\/p\u003e\u003ch2\u003eWhy the Original\u003c\/h2\u003e\u003cp\u003eÖhlins publishes dimensions for its service parts so a workshop can verify before it fits. Öhlins manufactures service parts on the same lines as production parts — there is no second quality. If you are unsure which number your unit takes, send us the model and serial number of the damper and we will look it up. Öhlins numbers do not follow a logic you can guess — always read them from the documentation.\u003c\/p\u003e\u003ch2\u003eGetting the Number Right\u003c\/h2\u003e\u003cp\u003eIf the unit is already open, compare the dimensions below with the part in your hand before ordering 01010-61. diameter 46 mm, length 321 mm is what distinguishes this number from its neighbours in the range. Öhlins gives the tube its diameter and its working length as a pair — a tube of the same bore but different length belongs to a different unit. The cylinder is one of the few damper parts that is genuinely wear-limited.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eWe are an authorised Öhlins service centre, so you do not have to source the tools and the nitrogen: send us the damper and we rebuild it with the correct parts and the correct setting.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-61\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 321 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648026829066,"sku":"01010-61","price":144.33,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-61_5f1399be-5ae1-4538-98cb-e93e1f1f1a97.png?v=1788870297"},{"product_id":"ohlins-cylinder-tube-46-247-01010-63","title":"Öhlins Cylinder tube 46\/247 – 01010-63","description":"\u003cp\u003eCylinder tube 46\/247, Öhlins part number 01010-63. The cylinder tube is the working bore: the piston runs inside it and every damping force is reacted by its wall.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eÖhlins part number 01010-63\u003c\/li\u003e\n\u003cli\u003eLength 247 mm\u003c\/li\u003e\n\u003cli\u003eOriginal Öhlins service part\u003c\/li\u003e\n\u003cli\u003eDiameter 46 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhere It Sits\u003c\/h2\u003e\u003cp\u003e01010-63 is the 46 mm, 247 mm version — Öhlins lists each size separately. Öhlins turns and hones each tube to a defined roundness, because an out-of-round bore leaks past the piston. Twin-tube dampers carry two concentric tubes and list them separately. A tube that has been bottomed hard often shows a ring mark; that is a reason to replace it.\u003c\/p\u003e\u003ch2\u003eOriginal Öhlins Part\u003c\/h2\u003e\u003cp\u003eAn original part keeps the unit within its published specification; a near-equivalent quietly moves it. The alternative to a service part is usually a new damper, which is why this catalogue exists. For a full rebuild, the seal kit plus the wear parts is usually the sensible order. Send us the model and serial number of your unit and we will confirm the position before you order.\u003c\/p\u003e\u003ch2\u003eIdentifying the Right Part\u003c\/h2\u003e\u003cp\u003eÖhlins identifies this position by the number 01010-63 in the exploded view for the unit it belongs to. Check diameter 46 mm, length 247 mm against what you have removed; a close size is not the same part. Length here is the working length, not the overall dimension, which is why two similar tubes are not interchangeable. Aluminium tubes are hard-anodised in the bore so the piston band has a hard surface to run against.\u003c\/p\u003e\u003ch2\u003eFitting and Setup Service\u003c\/h2\u003e\u003cp\u003eIf you would rather not open the damper yourself, we can do it — we are an authorised Öhlins service centre and rebuild these units as a matter of routine.\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cem\u003eBrand:\u003c\/em\u003e Öhlins\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003ePart Number:\u003c\/em\u003e 01010-63\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCategory:\u003c\/em\u003e Cylinder Tubes\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eDiameter:\u003c\/em\u003e 46 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eLength:\u003c\/em\u003e 247 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003eCountry of Origin:\u003c\/em\u003e Sweden\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Öhlins","offers":[{"title":"Default Title","offer_id":53648027877642,"sku":"01010-63","price":121.09,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/7831\/0410\/files\/01010-63_cd4ce2e1-1bd5-417d-b00c-9456fd4b8f59.png?v=1788870299"}],"url":"https:\/\/inter-pace.com\/collections\/suspension-tubes-bodies.oembed?page=4","provider":"Inter-Pace","version":"1.0","type":"link"}